Managing transport services in a CPE template

To display the table of transport services in a CPE template, go to the SD-WAN → CPE templates menu section, click the CPE template, and select the Transport services tab. Information about transport services is displayed in the following columns of the table:

• Name is the name of the transport service.
• QoS name is the name of the quality of service rule for the service interface, which is automatically created for connecting the CPE device to the transport service.
• Stage is the state in which the CPE device connects to the transport service:
  • Before activation means that the CPE device connects to the transport service before this CPE device is enabled.
  • After activation means that the CPE device connects to the transport service after this CPE device is enabled.

  You can select which state the CPE device is in after registration when adding a CPE device.

• Type is the type of the transport service:
  • P2M
  • M2M
  • L3 VPN
• Connection settings contains information about the service interface that is automatically created for connecting a CPE device to the transport service:
  • Role of the service interface:
    • Leaf
    • Root

    Displayed only if the value in the Type column is P2M.

  • Traffic classification type on the service interface:
    • Access
    • VLAN
    • Q-in-Q
  • Outer VLAN tag of the service interface. Displayed only if the traffic classification type on the service interface is VLAN or Q-in-Q.
  • Inner VLAN tag of the service interface. Displayed only if the traffic classification type on the service interface is Q-in-Q.

Adding a transport service to a CPE template

To add a transport service to a CPE template:

1. In the menu, go to the SD-WAN → CPE templates subsection.

   A table of CPE templates is displayed.

2. Click the CPE template to which you want to add a transport service.

   The settings area is displayed in the lower part of the page. You can expand the settings area to fill the entire page by clicking the expand icon . By default, the Information tab is selected, which displays general information about the CPE template.

3. Select the Transport services tab.

   A table of transport services is displayed.

4. Click + Transport service.
5. This opens a window; in that window, in the Name field, enter the name of the created transport service. If the actual name of the transport service does not match the name specified in the CPE template, the CPE device does not connect to the transport service.
6. In the QoS name field, enter the name of the created quality of service rule for the service interface, which is automatically created for connecting the CPE device to the transport service. If the actual name of the quality of service rule does not match the name specified in the CPE template, the quality of service rule is not applied to the service interface.
7. In the Stage drop-down list, select the state in which the CPE device connects to the transport service:
   • Before activation means that the CPE device connects to the transport service before this CPE device is enabled.
   • After activation means that the CPE device connects to the transport service after this CPE device is enabled.

   You can select which state the CPE device is in after registration when adding or manually registering a CPE device.

8. In the Type drop-down list, select the type of the transport service:
   • P2M If you select this option in the Role drop-down list, select the role of the service interface that is automatically created for connecting the CPE device to the transport service:
     • Leaf
     • Root
   • M2M
   • L3 VPN If you select this option, do the following:
     1. In the IP address field, enter the IP address of the L3 interface.
     2. In the Mask field, enter the length of the L3 interface prefix. Range of values: 0 to 32.

   If the actual type of the transport service does not match the type specified in the CPE template, the CPE device does not connect to the transport service.

9. In the Encapsulation drop-down list, select the traffic classification type on the service interface that is automatically created for connecting the CPE device to the transport service:
   • Access Default value.
   • VLAN If you select this option, in the VLAN ID field, enter the outer VLAN tag of the service interface. Range of values: 1 to 4094.
   • Q-in-Q If you select this value, configure the L3 interface that is automatically created and mapped to the service interface:
     1. In the VLAN ID field, enter the outer VLAN tag of the service interface. Range of values: 1 to 4094.
     2. In the Inner VLAN ID field, enter the inner VLAN tag of the service interface. Range of values: 1 to 4094.
10. Click Create.

    The transport service is created and displayed in the table.

11. In the upper part of the settings area, click Save to save CPE template settings.

Editing a transport service in a CPE template

To edit a transport service in a CPE template:

1. In the menu, go to the SD-WAN → CPE templates subsection.

   A table of CPE templates is displayed.

2. Click the CPE template in which you want to edit a transport service.

   The settings area is displayed in the lower part of the page. You can expand the settings area to fill the entire page by clicking the expand icon . By default, the Information tab is selected, which displays general information about the CPE template.

3. Select the Transport services tab.

   A table of transport services is displayed.

4. Click Edit next to the transport service that you want to edit.
5. This opens a window; in that window, if necessary, edit the transport service settings. For a description of the settings, see the instructions for adding a transport service to a CPE template.
6. Click Save.

   The transport service is modified and updated in the table.

7. In the upper part of the settings area, click Save to save CPE template settings.

Deleting a transport service from a CPE template

Transport services that are deleted in the CPE template cannot be restored.

To delete a transport service in a CPE template:

1. In the menu, go to the SD-WAN → CPE templates subsection.

   A table of CPE templates is displayed.

2. Click the CPE template in which you want to delete a transport service.

   The settings area is displayed in the lower part of the page. You can expand the settings area to fill the entire page by clicking the expand icon . By default, the Information tab is selected, which displays general information about the CPE template.

3. Select the Transport services tab.

   A table of transport services is displayed.

4. Click Delete next to the transport service that you want to delete.

   The transport service is deleted and is no longer displayed in the table.

5. In the upper part of the settings area, click Save to save CPE template settings.